Overview

The Foundry Mini Panels offer up to eight zones of DMX controlled lighting with fully rated 20 A relays and optional 010 V control per zone. The Mini Panel features a Demand Response input for energy saving integration and a UL 924 emergency lighting control bypass with power loss sense. The Mini Panel is available in flush-mount or surface-mount options and can be located in an air plenum to be easily tucked out of sight.

APPLICATIONS

• Arena and stadium suites
• Office buildings
• Conference and meeting rooms
• Healthcare facilities
• Houses of worship
• Classrooms
• Hospitality and restaurants
• Retail

FEATURES

• Switched power control of four or eight circuits with 010 V dimming
• 120 or 277 VAC power input per zone
• 20 A fully rated relays for use with general purpose, tungsten, fluorescent, LED and plug loads
• 010 V dimming output per zone for direct connection to dimming ballasts and LED drivers
• Demand Response load shedding contact input
• Flush-mount and surface-mount options
• UL924 control bypass via
  • Contact closure input
  • Normal power loss sense feed terminals
• DMX controlled and RDM configurable

REGULATORY AND COMPLIANCE

• cULus and UL 924 LISTED
• Rated for plenum installation
• Suitable for plug load control

Specifications

FUNCTIONAL

• Control for up to eight zones of switching for lighting and plug loads
• Control for up to eight zones of 010 V dimming for LED drivers and fluorescent ballasts
• UL 924 emergency-lighting control via contact closure and power loss sense feed terminal
• Demand Response input provided by a power company can enforce a maximum level per circuit while active
• Supports USITT DMX512-A (ANSI E1.11)
• Supports RDM (ANSI E1.20)

MECHANICAL

• Constructed of 16-gauge cold-rolled steel, finished in fine-textured, black powder coat
• Wall-mount installation; rated for installation in plenum air space
• Class 1 voltage barrier prevents access to line-voltage wiring with front panel removed
• Available in flush-mount and surface-mount options
• Optional voltage divider allows for separation of normal and emergency circuits in a single controller where allowed by local codes

ELECTRICAL

• 100277 VAC, 50/60 Hz power input per circuit with support for pass thru to multiple circuits
• 100277 VAC single phase sense feed input
• Supports 120 VAC and 277 VAC circuits within the same panel
• 20 A, fully-rated bi-state latching relay per output
• 010 VDC control rated for up to 100 mA sink per output
  • 010 V outputs are fully isolated from ground to 2500 V RMS
• Control circuit power draw: 0.5A
• Rising clamp screw terminal wiring connections for:
  • Line-voltage relay power input, output and pass-through with support for 2.5-10 mm2 (14-8 AWG) wire
  • Controller power input and UL 924 Sense circuit with support for 0.5-4 mm2 (20-12 AWG) wire
  • Low-voltage 010 V dimming output per zone with support for 0.5-1.5 mm2 (22-16 AWG) wire
  • Separate normal power sense feed input for UL 924 emergency lighting bypass
  • UL 924 emergency lighting control contact closure input with support for 0.5-1.5 mm2 (22-16 AWG) wire
  • Demand Response contact input with support for 0.5-1.5 mm 2 (22-16 AWG) wire
• Demand Response input supports Normally Open (NO) operation
• UL 924 contact closure input supports normally open (NO) or normally closed (NC) operation
• Onboard status indicators for controller power, DMX signal, Demand Response input, and UL 924 emergency lighting control
• Slide switch configuration for:
  • UL 924 operation (NO/NC)
  • UL 924 inclusion per circuit (on/off)

RELAY RATINGS

• 20 A Magnetic Ballast (HID)
• 16 A Electronic Ballast
• 20 A Tungsten
• 20 A (120 A Locked-rotor) Motor @ 120 VAC
• 14 A (84 A Locked-rotor) Motor @ 277 VAC
• Relays are mechanically held
• Lifespan:
  • 100,000 cycles at full resistive load
  • 30,000 cycles motor, inductive or tungsten

DMX INPUT PORT

• Optically-isolated input from the Mini Panel electronics
• Withstands fault voltages of up to 250VAC
• Integrated DMX/RDM termination

CONFIGURATION

• Remote configuration available via RDM devices such as:
  • ETC control console with RDM functionality
  • ETC DMX/RDM gateway networked to a device running ETC Net3 Concert software
• Manual configuration of the starting DMX address, UL 924 bypass, and Demand Response on the controller

THERMAL

• Ambient room temperature: 050 C (32122 F)
• Ambient humidity: 595% (non-condensing)